AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Diptrace pads in circle12/16/2023 ![]() ![]() I might typically have avoided (maybe needlessly) multiple instances of a sheet connector on a single sheet for fear of confusion. One unexpected benefit arises when having to use the same line on opposite ends of the sheet. Given clear enough names for the lines going into the bus, it's not particularly hard to understand. I decided to create a bus called PSU for the lines related to this section which would be needed between sheets. This is a sheet I'm working on which is one of several sheets in the power supply/distribution section of a bigger project: There is, however, nothing to say they have to be limited to that schema. I am used to the traditional use of busses to carry signals that are homogeneous except in magnitude, such as data lines, address lines, IRQs, etc. This doesn't strictly answer the question exactly as stated, so I'm not going to mark this as the answer, but I'll post what I've found as a satisfactory approach.īasically, I adapted my style a bit more to the capabilities and omissions of the program. 12-pin header- that spans a few pages, and you can connect to that connector instead. ![]() Maybe you can have connector netport- I.e. It took me less than a minute.) The positive is that you can create your own custom netports. Unfortunately you'll have to at least once create it. (Not shown is the label of the netport, which is both Net 0.)Īs long as you change the names of the netport, you can have as many as you'd like. When highlighting the trace to one of the resistors connected to SIGNAL, the entire port is highlighted. The two SIGNAL ports connected to two different resistors, and a CLOCK port connected to a third resistor. For instance, I have two different types of connector: SIGNAL and CLOCK. Make sure to change the type of your connector to the same port that you want. In your schematic editor, add your components. Make sure that the Part Type is Net Port. In component editor, preferably Discrete Schematic, Component > Add New to Library.ĭraw a port connector that you're use to. I just have to assume there's a better way than what I'm doing, 'cus it's quite tedious.Make your own connector. Is there, perhaps, a field that would accept something like "C 4.7UF 5.0" (I just made that up) to return any 4.7 uF cap with a 5 mm lead spacing, regardless of manufacturer or exact manufacturer part number? Gibberish unless you work in TDK's stocking department. Is there some kind of standard labeling for parts that is not manufacturer dependent that I can use within the DipTrace filter? For example, the exact part number for my 4.7 uF cap is "FG28X5R1E475KRT06". But the best I've been able to do so far is to hunt-and-peck, just randomly searching through all the DipTrace cap components looking. I know that Digikey has a KiCad library that can be imported, but there's only a few thousand components in it.īack to my 4.7uF example in the OP, I'm sure there are many components for a capacitor within DipTrace that have a pattern suitable for my cap with 0.5mm dia leads spaced at 5mm. But how do I find a suitable match?Ĭlick to expand.I've certainly used filters, but haven't seen a DigiKey library within Diptrace. There is nothing particularly remarkable about this, and I'm sure there are many other parts with the exact same characteristics. It has a lead diameter of 0.5mm and a lead spacing of 5.0mm. Take, for example, a 4.7 uF through-hole ceramic capacitor from TDK. I'd be quite content to use a substitute symbol and pattern, but I don't know how to find one with exact hole sizing and spacing that matches my actual part. I know how to create a component from scratch in the component editor and pattern editor, but I don't want to have to do that for every piece in my project. With millions of components in the world out there, I'm not surprised that DipTrace's library doesn't have every one, but I am surprised that of all the parts I've looked for, it hasn't had a single one. But so far, not a single component I've looked for, from converters, resistors, inductors, to opamps, has shown up within the DipTrace library. I'm working on a schematic in DipTrace with the intent of creating a PCB, so the patterns associated with the component matters. I've searched a lot of threads and tutorials for this, but have so far not found anything helpful.
0 Comments
Read More
Leave a Reply. |